Items Covered
- a."Technology" (other than "technology" controlled by paragraphs .b and .c of this entry) "required" for the "development," "production," operation, installation, maintenance, repair, overhaul, or refurbishment of items controlled by ECCN 9A619 (except 9A619.y), ECCN 9B619 (except 9B619.y), ECCN 9C619, or ECCN 9D619 (except 9D619.y).
- b."Technology" (other than "build-to-print technology") "required" for the "development" or "production" of any of the following:
- 1. Front, turbine center, and exhaust frames;
- 2. Low pressure compressor (i.e., fan) "components" and "parts" as follows: Nose cones and casings;
- 3. High pressure compressor "components" and "parts" as follows: Casings;
- 4. Combustor "components" and "parts" as follows: Casings, fuel nozzles, swirlers, swirler cups, deswirlers, valve injectors, and igniters;
- 5. High pressure turbine "components" and "parts" as follows: Casings
- 6. Low pressure turbine "components" and "parts" as follows: Casings;
- 7. Augmentor "components" and "parts" as follows: Casings, flame holders, spray bars, pilot burners, augmentor fuel controls, flaps (external, convergent, and divergent), guide and syncronization rings, and flame detectors and sensors;
- 8. Mechanical "components" and "parts" as follows: Fuel metering units and fuel pump metering units, valves (fuel throttle, main metering, oil flow management), heat exchangers (air/air, fuel/air, fuel/oil), debris monitoring (inlet and exhaust), seals (carbon, labyrinth, brush, balance piston, and "knife-edge"), permanent magnetic alternator and generator, eddy current sensors;
- 9. Torquemeter assembly (i.e., housing, shaft, reference shaft, and sleeve); or
- 10. Materials controlled by ECCN 9C619.b.
- c."Technology" "required" for the "development" or "production" of any of the following:
- 1. Low pressure compressor (i.e., fan) "components" and "parts" as follows: blades, vanes, spools, shrouds, blisks, shafts and disks;
- 2. High pressure compressor "components" and "parts" as follows: blades, vanes, spools, shrouds, blisks, shafts, disks, and impellers;
- 3. Combustor "components" and "parts" as follows: diffusers, liners, chambers, cowlings, domes and shells;
- 4. High pressure turbine "components" and "parts" as follows: shafts and disks, blades, vanes, nozzles, tip shrouds;
- 5. Low pressure turbine "components" and "parts" as follows: shafts and disks, blades, vanes, nozzles, tip shrouds;
- 6. Digital engine control systems (e.g., Full Authority Digital Engine Controls (FADEC) and Digital Electronic Engine Controls (DEEC)) "specially designed" for gas turbine engines controlled in this ECCN; or
- 7. Engine monitoring systems (i.e., prognostics, diagnostics, and health) "specially designed" for gas turbine engines and components controlled in this ECCN.
- d.through x. [Reserved]
- y.Specific "technology" "required" for the "development," "production," operation, installation, maintenance, repair, overhaul, or refurbishment of commodities controlled by 9A619.y or 9B619.y, or "software" controlled by ECCN 9D619.y.
Control Reasons Explained
This ECCN is controlled for the following reasons. Each reason maps to a column on the Commerce Country Chart, which determines whether a license is required for a given destination.
- NSNational Security
- Items that could contribute to the military potential of countries of concern. Check the Commerce Country Chart column for NS to determine license requirements.
- RSRegional Stability
- Items that could destabilize regions through conventional-arms build-up. Review RS columns on the Commerce Country Chart.
- ATAnti-Terrorism
- Basic anti-terrorism controls that apply to most items on the CCL. A license is required for exports to countries designated as state sponsors of terrorism.
- UNUnited Nations
- Items subject to United Nations Security Council sanctions or embargoes. Check current UN resolutions for applicable restrictions.
Common Questions About 9E619
What does ECCN 9E619 cover?
ECCN 9E619 is an entry on the Commerce Control List (Aerospace). The List of Items Controlled below describes the products, software, or technology captured by this classification. Compare your item against those parameters when self-classifying.
How do license requirements work for this ECCN?
License need depends on the control reasons shown for this code (for example NS, RS, MT, AT), the destination country, and how your transaction maps against the Commerce Country Chart, de minimis, and other EAR provisions. This page is a research aid only. Confirm against the current rule text and your specific facts before exporting.
Where is the official text for this ECCN?
The legal text appears in Supplement No. 1 to part 774 of the Export Administration Regulations (15 CFR Part 774). Use the official BIS link on this page to open the current supplement entry for this ECCN.
What if my product matches more than one ECCN?
When several ECCNs appear to fit, the controlling entry is usually the one that is most specific to your item's form, function, or technical limits. Cross-references in the List of Items Controlled and related ECCNs listed on this page are common starting points for narrowing the choice.
How often should I re-check this classification?
The Commerce Control List changes when BIS publishes new or amended rules. Revisit the official entry when regulations update, when the product's technical parameters change, or when the destination, end-user, or end-use of a transaction changes.
What do the control reason codes mean?
Each control reason (NS, RS, MT, AT, etc.) maps to a column on the Commerce Country Chart in Supplement No. 1 to part 738 of the EAR. When a control reason applies to your ECCN and the destination country has an X in that column, a license is generally required unless an exception applies. See the Control Reasons Explained section on this page for details on each code.